Untitled Document

Alarm Systems
FS301K- Remote control & Key pad	Two channel RF remote control Command keypad with six feet of cable Control module. Dimensions - 4.5” X 3.0” X 1.25” Five amp fuse and water-resistant fuse holder Stainless steel mounting hardware Warning decal ¨ 16 Pin plug ¨ 19.8” antenna
FS301K-DSP Remote control & Key pad with deck sensor processor	Two channel RF remote control Command keypad with six feet of cable Internal Deck Sensor Processor Control module. Dimensions - 4.5” X 3.0” X 1.25” Five amp fuse and water-resistant fuse holder Stainless steel mounting hardware Warning decal ¨ 16 Pin plug ¨ 19.8” antenna
FS301 Remote control alarm system	Two channel RF remote control Control module. Dimensions - 4.5” X 3.0” X 1.25” Five amp fuse and water resistant fuse holder Stainless steel mounting hardware Warning decal 16 Pin plug 19.8” antenna
FS301-DSP Remote control alarm system with deck sensor processor	Two channel RF remote control Internal Deck Sensor Processor Control module. Dimensions - 4.5” X 3.0” X 1.25” Five amp fuse and water resistant fuse holder Stainless steel mounting hardware Warning decal 16 Pin plug 19.8” antenna
FS201 Touch pad alarm system	Command Keypad with six feet of cable Control module. Dimensions - 4.5” X 3.0” X 1.25” Five amp fuse and water resistant fuse holder Stainless steel mounting hardware Warning decal 16 Pin plug 19.8" antenna
FS201 Touch pad alarm system with deck sensor processor	Command Keypad with six feet of cable Internal Deck Sensor Processor Control module. Dimensions - 4.5” X 3.0” X 1.25” Five amp fuse and water resistant fuse holder Stainless steel mounting hardware Warning decal 16 Pin plug 19.8" antenna
Magnetic Sensors
Canvas Sensor	For protection of canvas covers. The CS1 is a direct replacement for existing canvas snaps. The switch is weatherproof, normal closed and is easy to install. Switch is made of brass and stainless steel. Canvas Sensor - Part # CS1
Push Button Sensor	The MG5 flush mounts in doorways and hatches where a completely concealed sensor is desired. The flanged push button switch is normally closed and has comes with 12" of wire switch diameter is .75". Flanged Push Button Sensor- Part # MG5
Mini Wide Gap Sensor	The MG10 protects entrance hatches, and other areas where a small surface mount magnetic switch is desired. The switch is normally closed and has a 1.0" gap. The switch is 1.25" X .375" X .375" and has 6 ft. of wire. Mini Wide Gap Sensor - Part # MG10
Flush Mount Sensor	The MG15 flush mounts in doorways, hatches and stereo compartments, where a completely concealed sensor is desired. The cylinder shaped switch is normally closed and comes with 12" of wire. Switch diameter is .25". Flush Mount Sensor - Part # MG15
Engine Hatch Sensor	Secures large engine and storage compartments. Reduces installation time while providing a factory finish. Switch gap is 2.5". Switch is pre-wired with 20 feet of shielded wire and comes with a complete selection of stainless mounting hardware. Switch dimensions - 2.0" X .50" X .50". Engine Hatch Sensor - Part # MG20
Instrument Sensor	The MG1005 secures radar sets, depth finders and equipment that is easily removed. When sensor is removed the normally closed contacts open. Instrument Sensor - Part # FS1005
Motion Detectors
Cabin Motion Detector	The MD100 cabin motion detector combines infra-red and micro-wave technology to eliminate false alarms and excessive wiring of cabin windows and doors. Security coverage is a maximum area of 40' X 30'. Power consumption is 25 milli-amps. Dimensions are 4" X 3" X 2" and comes with stainless steel mounting hardware and 25 feet of four conductor wire. Dual-Tec Motion Detector - Part # MD100
Photo Electric Beam	Miniature 3/4” photo eyes can be mounted across decks, bridges, walkways, etc. When the beam is broken the alarm activates. Can be used as a pre-entry sensor. Power consumption is approximately 50 milli-amps. Processor dimensions are 4” X 2” X 1.5”. Kit contents: 1 Sensor processor and 2 photo-eyes with mounting plates. Part # - OS1C
Pressure Mat	The FS17 pressure mat is weather-resistant and measures 17” X 23” by only .125” thick. The mat is normally open and comes wired with 3 feet of #18 AWG wire. Part # - FS17
TrailerSensor	The TS1 sensor detects movement of a boat while it is stored on a trailer. TS1 sensors are usually mounted in the bow next to the mooring hook. Part # - TS1
Mercury Switch	Mercury switch can secure outboards and equipment on boats kept on trailers. Part # - MS1
Deck Sensor	FA1 deck sensors work in conjunction with the optional internal Deck Sensor Processor (DSP). The DSP is available on all Flagship Marine alarms. FA1 sensors easily mount under a boat’s deck with epoxy and can secure up to five square feet. One or two FA1 sensors usually provide enough coverage for most boats. When an intruder steps on the boat’s deck, the FA1 sends data to the DSP activating the alarm. The miniature FA1 sensor measures 2.5” X .75” X .25”. Kit comes with epoxy and one deck sensor. Part # - FA1
Internal Deck Sensor Processor FS201-DSP FS301-DSP FS301K-DSP	Deck Sensor Processors (DSP), are built-into specific Flagship Marine alarms. The (DSP) monitors up to six FA1 deck sensors. When an intruder steps on the boat’s protected deck, the DSP compares the deck movement and duration of the footstep to the boat’s stored deck movement signature activating the alarm. The DSP filters out false alarms caused by temperature or boat movement. Power consumption is 3 milli-amps and low enough for most moored boats. The following alarm systems come with internal Deck Sensor Processors: FS201-DSP, FS301-DSP and the FS301K-DSP

Electronic Sirens
15 Watt Siren	This 15 watt electronic siren is designed to be concealed under gunnels, dashboards and storage areas. Part # ES15
20 Watt Siren	This easy-to-conceal Single Tone 111 dB20 Watt Weatherproof Siren provides multiple benefits including weatherproof construction, simple installation and loud sound output. Part # ES20
20 Watt Siren	The ES30 is an attractive 30 watt electronic siren that physically looks like a P.A. speaker. It usually mounts on radar arches and hardtops. Siren is white and comes with stainless mounting hardware. Part # - ES30

System Enhancement Components
Command Keypad	The command keypad can be added to all systems or as a second keypad on the FS201 and FS301K for convenient arming Part # - PK1 (Pre-wired with six feet of wire) Part# - PK1-20 (Pre-wired with 20 feet of wire)
Remote Control	The RC2 remote control works with the FS301 and FS301K alarm systems. Up to ten code-hopping RC2s can be programmed to any alarm. Part # - RC2
Driver Relay	The FS401 driver relay drives high power loads (up to 20 amps) such as flashing lights, boarding lights and multiple sirens. It can be also be used to disable the boat's ignition system or trigger communicators. Driver Relay - Part # FS401
Sensor 2-Wire	One hundred feet of white two conductor stranded #20 AWG wire for connecting magnetic sensors and other two wire devices. Part # - SW20
Sensor 4-Wire	One hundred feet of four conductor stranded #22 AWG wire for connecting motion detectors and other four wire devices. Part # - SW22/4
Shielded Sensor 2-Wire	One hundred feet of shielded two conductor stranded #22 AWG wire for connecting deck sensors. Part # - OSW2/2
Power Harness Kit	The power harness kit simplifies wiring and provides reliable connections from the alarm to the boat’s battery, accessories, keypads and zone terminations. Kit contents: Two ring connectors, #16 AWG vinyl jacketed power cable (specify length XXft.) with terminations tailored to your alarm. Part # - PHK - (XX ft.)
System Instructions	Extra set of System Instructions for all alarms systems. Part # - INS01
Red Led	External red LED for visual status of all alarm systems. Part # - LED-1S
Warning Decal	Red weather-resistant outside warning decal. Part # - WD1
Smoke/Heat Detector	The CST449 monitors for both smoke and high temperature. Part # - CST449
4 Watt Radio Link	Four watt, CB frequency pager. Part # ALA-400P
Remote Battery	Replacement battery for the RC2 remote control. Part # - AB-101
Carbon Monoxide Alarm	Activates internal siren and 24-Hour zone of all alarms. Attractive design with very low power consumption (8 milli-amps). Part # ES-240CO
Mini Strobe Light	Miniature red strobe light with mounting tabs. Strobe is water tight, extremely bright and comes with stainless steel mounting hardware. Part # - SL-12
Voice Dialer	The dialer connects to standard phone lines. When siren sounds, the voice dialer sends a 32 second voice message and pages the boat owner. Part # - USP1